STRUCTURAL ANALYSIS OF HYBRID VERTICAL TAKE-OFF LANDING (VTOL) CONFIGURATION
Keywords:
VTOL, Hybrid UAV, quadrotor, fixed wing, vibrationAbstract
Maximizing flying qualities of a UAV is not a new topic in the aeronautical branch. Therefore, there is a significant amount of growing interest shown by researchers to integrate the flying mechanism of both conventional fixed wing UAV and rotorcraft UAV and thus, results in the birth of hybrid VTOL UAV. This paper investigates the difference in wing deflection of a hybrid VTOL UAV, a quadrotor fixed-wing with two independent propulsion systems and a conventional fixed wing. Quantitative method is chosen throughout this study where data collected are mainly from experiments and literature study. Firstly, the general wing specification is determined. To achieve this, a design analysis is conducted based on theoretical calculation and data from previous researches. The most suitable wing is found to be a straight wing with 0.3m chord length and 2m wingspan. Following that, a structural analysis is done to compare the difference in wing deflection for both mentioned UAV. After fabricating the model wing spar, an experimental set up for vibration test to determine wing deflection of a quadrotor fixed-wing is being prepared and ran. At the same time, wing deflection of a fixed wing UAV is calculated by using beam deflection equation. The maximum deflection obtained is 0.0865385m and 0.0002516m respectively. The result shows that maximum deflection at wing tip for hybrid VTOL is higher than a conventional fixed wing. Factors that contributed to this finding were the concentrated upward lift force and also fluctuated force coming from vibration of the motor driven propeller.
References
Md. S. A., Tariq. H. & Kazi. M. H. (2018). Development of a Multi-purpose Hybrid & Portable Surveillance Drone for Security and Disaster Management. Journal of Science and Technology Research 2016-2017, 52-56.
Austin, R. (2010). Unmanned Aircraft Systems. New Delhi, British Library.
Muhammad Fadhil, J., Mastura, A. W., Mohd Nazri, M. N., Norazila, O. & Mohd Zarhamdy, M. Z. (2018). Design and Analysis Performance of Fixed Wing VTOL UAV. Journal of Transport System Engineering 5:1, 17-25
Gunarathna, J. K. & Munasinghe, R. (2018). Development of a Quadrotor Fixed-Wing Hybrid Unmanned Aerial Vehicle. Moratuwa Engineering Research Conference (MERCon). Moratuwa.
Abd Rahman, Y. A., Hajibeigy, M. T., Al-Obaidi, A. S. M. & Cheah, K. H. . (2018). Design and Fabrication of Small Vertical-Take-Off-Landing Unmanned Aerial Vehicle. MATEC Web of Conferences.
Saeed, A. S., Younes, A. B., Cai, C. & Cai, G. (2018). A SURVEY OF HYBRID UNMANNED AERIAL VEHICLES. Progress in Aerospace Sciences.
L.Kohlman, D. (1981). Introduction to V/STOL Airplanes. Iowa: The Iowa State University Press.
Gu, H., Lyu, X., Li, Z., Shen, S., & Zhang, F. (2017). Development and experimental verification of a hybrid vertical take-off and landing (VTOL) unmanned aerial vehicle(UAV). 2017 International Conference on Unmanned Aircraft Systems, ICUAS 2017, 160–169. https://doi.org/10.1109/ICUAS.2017.7991420
Intwala, A. & Parikh, Y. (2015). A Review on Vertical Take Off and Landing (VTOL) Vehicles. International Journal of Innovative Research in Advanced Engineering (IJIRAE), 186-191.
Tielin, M., Chuanguang, Y., Wenbiao, G., Zihan, X., Qinling, Z., & Xiaoou, Z. (2018). Analysis of technical characteristics of fixed-wing VTOL UAV. Proceedings of 2017 IEEE International Conference on Unmanned Systems, ICUS 2017, 2018-Janua, 293–297.
https://doi.org/10.1109/ICUS.2017.8278357
Barnes W. McCornick, J. (1967). Aerodynamics of V/STOL Flight. California: Academic Press Inc.
Felix, F., Carsten, B. & Cees. B. (2017) A Review of Configuration Design for Distributed Propulsion Transitioning VTOL Aircraft. 2017 Asia-Pacific International Symposium on Aerospace Technology, Seoul, Korea.
Ashraf, M. K. & Alex, R. S. (2018). Design Methodology for Hybrid (VTOL + Fixed Wing) Unmanned Aerial Vehicles. Aeronautics and Aerospace Open Access Journal, 165-176.
Puspita, T. D., Ghozali, S. H., Muhammad, R. K., Aris, B. & Agus, B. (2016). Design of Separate Lift and Thrust Hybrid Unmanned Aerial Vehicle. The Journal of Instrumentation, Automation and Systems, 45-51.
Hunsaker, D. (2007) ‘Post Stall Behavior of a Lifting Line Algorithm’, (May 2007), pp. 1–7.
Krishnaiah, A., Chakkingal, U. and Kim, H. S. (2008) ‘Mechanical properties of commercially pure aluminium subjected to repetitive bending and straightening process’, Transactions of the Indian Institute of Metals, 61(2–3), pp. 165–167.
Douglas, C. M., Elizabeth, A. P. and Geoffrey, V. (2012) Introduction to Linear Regression Analysis. John Wiley & Sons, Inc.
Czyba, R., Lemanowicz, M., Gorol, Z. and Kudala, T. (2018) ‘Construction Prototyping, Flight Dynamics Modeling, and Aerodynamic Analysis of Hybrid VTOL Unmanned Aircraft’, Journal of Advanced Transportation, 2018, pp. 13–16.
Watkins, S., Ravi, S. and Loxton, B. (2010) ‘The effect of turbulence on the aerodynamics of low Reynolds number wings’, Engineering Letters, 18(3).
NCYU (no date) ‘Mechanics of Materials Chapter 6 Deflection of Beams’.
Downloads
Published
How to Cite
Issue
Section
License
Copyright of articles that appear in Journal of Transpot System Engineering (JTSE) belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions or any other reproductions of similar nature.
Disclaimer: The views and opinions expressed in the articles are those of the authors and do not necessarily reflect the official policy or position of the JTSE. Examples of analysis performed within are only examples and they should not be utilized in real-world. Assumptions made within the analysis are not reflective of the position of any JTSE entities.